국문목차
표제지=0,1,3
목차=i,4,2
그림 목차=iii,6,1
ABSTRACT=iv,7,1
I. 서론=1,8,1
1. 연구 배경=1,8,1
2. 연구목적 및 방법=2,9,2
II. 이론적 배경=3,10,1
1. 판넬의 초기 좌굴응력=3,10,2
2. 보강재에 의해 측면 구속된 외피(skin)의 좌굴응력=4,11,1
2.1 좌굴응력의 소성 영역에 대한 보정=5,12,2
2.2 초기 불규칙 형상에 대한 고려=6,13,2
2.3 단순 지지된 외피의 좌굴응력=7,14,1
2.4 탄성영역으로 가정한 보강재에 의해 측면구속된 외피의 좌굴응력=8,15,1
2.4.1 측면 구속계수 결정=8,15,4
2.4.2 보강재(stringer) 단면 계수=11,18,2
2.4.3 측면 구속상수 결정=13,20,8
3. 보강재 국소 좌굴응력=21,28,1
3.1 자유 플랜지 국소 좌굴응력=21,28,1
3.2 접촉 플랜지 국소 좌굴응력=22,29,1
3.3 웹 국소 좌굴응력=23,30,1
III. 고찰=24,31,1
1. 프로그램 구성=24,31,1
2. 보강재 두께 변화에 따른 판넬의 초기 좌굴응력 변화=24,31,2
3. 보강재 높이 변화에 따른 초기 좌굴응력 변화=26,33,2
4. 보강재 자유 플랜지 길이 변화에 따른 초기 좌굴응력 변화=27,34,2
IV. 결론=29,36,1
참고문헌=30,37,2
Fig.1. Tangent modulus and secant modulus=6,13,1
Fig.2. Equilibrium of a sturdy-stiffener element dx=9,16,1
Fig.3. Dimension of the Z-section Stringer=11,18,1
Fig.4. General design chart giving values of k for eoual restraint coefficient(ε) on each side edges of the plate=18,25,1
Fig.5. Special design chart giving values of k for equal restraint coefficient(ε) on each side edges of the plate when the restraint of the half wave length(λ)=20,27,1
Fig.6. Initial buckling stress of the panel vs. stringer height=24,31,1
Fig.7. Panel Initial buckling stress vs. stringer height(h=5ts)=26,33,1
Fig.8. Panel Initial buckling stress vs. stringer height(h=15ts)=26,33,1
Fig.9. Panel Initial buckling stress vs. stringer height(h=25ts)=27,34,1
Fig.10. Panel Initial buckling stress vs. stringer height(h=35ts)=27,34,1
Fig.11. Panel Initial buckling stress vs. stringer height(bf=0.3h)=28,35,1
Fig.12. Panel Initial buckling stress vs. stringer height(bf=0.5h)=28,35,1
Fig.13. Panel Initial buckling stress vs. stringer height(bf=0.8h)=28,35,1