표제지
Abstract
요약
목차
제1장 서론 13
1.1. 연구배경 13
1.2. 연구목적 및 주요 연구내용 14
제2장 이론적 배경 16
2.1. 사출 금형의 개요 16
2.1.1. 사출 성형 16
2.1.2. 사출 성형의 분류 16
2.1.3. 사출 성형의 기본 동작 21
2.2. 사출 성형 재료 22
2.2.1. 열가소성(Thermoplastic) 수지 22
2.2.2. 열경화성(Thermoset) 수지 23
2.2.3. 금형 사출 성형기 24
2.2.4. 사출기 주변기기 24
2.3. 사출 금형 주요인자 25
2.3.1. 형체력 25
2.3.2. 사출압력 25
2.3.3. 금형 온도 26
2.3.4. 사출 속도 26
제3장 실험 27
3.1. 사출 금형 제작 27
3.2. 금형 설계 28
3.3. 금형 제작 29
3.3.1. 소재 선정 29
3.3.2. 수지 선정 36
3.4. 사출 및 최적 조건 38
3.4.1. 실험 장치 38
3.4.2. 실험 방법 39
제4장 결론 51
참고문헌 52
[표3.1] STAVAX Ingredients 30
[표3.2] Recommended hardness by mold type 30
[표3.3] Stavax physical data when quenched and tempered to HRC 50 31
[표3.4] Stavax tensile strength at room temperature 31
[표3.5] Stavax face and square shoulder milling 32
[표3.6] Stavax End Mill Machining 32
[표3.7] Stavax face and square shoulder milling conditions 33
[표3.8] Stavax End Mill Milling Conditions 33
[표3.9] Nimax Ingredients 35
[표3.10] Nimax physical properties 35
[표3.11] Nimax tensile strength 35
[표3.12] Nimax face and square shoulder milling conditions 36
[표3.13] Nimax End Mill Milling Conditions 36
[표3.14] FANUC S-2000i300B SPEC 38
[표3.15] Forming Analysis (CAE) Results 47
[그림2.1] Comparison of general mold products (top) and compression mold products (bottom) 17
[그림2.2] Stress comparison 18
[그림2.3] Transparent Polycarbonate Pellets 21
[그림2.4] Molecular chain arrangement of crystalline resin and amorphous resin 23
[그림2.5] Cross linking of thermosetting resins and thermoplastic resins 24
[그림3.1] Two-Plate Structure Injection Mold 27
[그림3.2] Mobile Phone Back Cover Modeling 28
[그림3.3] Lower Core of ICM Mold 34
[그림3.4] FANUC S-2000i300B injection molding machine 38
[그림3.5] ICM mold operation sequence 39
[그림3.6] ICM Injection Machine Signal Cycle 39
[그림3.7] t 1.1mm before compression molding 40
[그림3.8] t 0.6mm after compression molding 41
[그림3.9] Compression Injection Filling Pattern 42
[그림3.10] Normal injection filling pattern 43
[그림3.11] Birefringence Comparison 44
[그림3.12] A-shaped deformation and bending 45
[그림3.13] Clamping pressure & product t 48
[그림3.14] Clamp Distance & Clamp Pressure 49
[그림3.15] Product t & clamp pressure 50