|
(A) dual-branch inverted residual network guided by mixed loss for the bearing fault diagnosis with few samples
|
Jie Liu, Ting Wang, Hai Wang, Jingsong Xie, Kai Zhang
|
p. 1-13
|
|
|
|
|
|
Horizontal wheels dynamics characteristics of straddled monorail vehicles when curves are passed
|
Shengfei Zhou, Ying Zhang, Guibin Huang, Kuilin Qu, Dongwei Yi
|
p. 15-22
|
|
|
|
|
|
Acoustic propagation properties of expansion chamber phononic crystals for water jet guided lasers
|
Fan Yang, ChaoZhong Meng, YuQiang Wang, HongJie Fan, Jiaxin Yu
|
p. 23-31
|
|
|
|
|
|
On the need to characterize fatigue damage behavior in additively manufactured AlSi10Mg using signal energy parameters
|
M.M. Mubasyir, S. Abdullah, M.K. Faidzi, S.S.K. Singh, C.H. Chin, Z. Wahid
|
p. 33-43
|
|
|
|
|
|
Multi-representation unsupervised domain adaptation hybrid convolutional neural network for machinery fault diagnosis
|
Wenhua Chen, Jianbin Li, Sixing Wu, Qi Wang
|
p. 45-59
|
|
|
|
|
|
Effects of cage pocket wear and thermal expansion on the nonlinear dynamics of ceramic bearings
|
Shiying Zhang, Bo Song, Zinan Wang, Xiaotian Bai, Zhenning Su
|
p. 61-72
|
|
|
|
|
|
Dynamic modeling and performance analysis of suspended weight gravity energy storage system under wind loads
|
Kun Cai, Yifeng Han, Yesen Zhu, Haodong Cheng, Yu Chang, Wan Sun, Jun Wang, Guanggui Cheng, Zhongqiang Zhang
|
p. 73-86
|
|
|
|
|
|
Multi-objective design optimization of angular contact ball bearings considering thermal expansion and clearance variation
|
Minhyeok Lee, Junho Suh, Bokseong Choe
|
p. 87-104
|
|
|
|
|
|
Development of a dynamic model for axle load transfer induced by traction torque in railway vehicles
|
Ju Seok Kang
|
p. 105-116
|
|
|
|
|
|
Acoustic-based diagnosis of impeller and bearing faults in centrifugal pumps using optimized ensemble learning models
|
Savaş Koç, Idris Saçaklıdır
|
p. 117-131
|
|
|
|
|
|
Vibration analysis of bolted cantilever plates using an artificial spring model with contact pressure distribution
|
Xiang Zhang, Wenguang Liu, Long Cheng, Zhigen Lin, Hong Wang
|
p. 133-145
|
|
|
|
|
|
Effect of rotation on load capacity in slot restrictor hydrostatic air bearings
|
Shinji Kajiwara, Naoki Okuda, Tomoya Kinugawa, Shinya Kikutani
|
p. 147-157
|
|
|
|
|
|
(A) method for solving structural modal parameters based on complete modal decomposition
|
Shilong Zeng, Hongyuan Du
|
p. 159-171
|
|
|
|
|
|
Remaining useful life prediction of gears : an IAPO-MHA-HyVAE-based approach
|
Xiangmin Chen, Yonghui Li, Hanlin Lei, Kang Zhang, Shilong Hu, Yang Su
|
p. 173-182
|
|
|
|
|
|
LMI-based output feedback control for rear suspension : a comparative study of MR dampers and active suspension systems for pickup trucks
|
Yeongwoo Yang, Yonghwan Jeong
|
p. 183-192
|
|
|
|
|
|
Dynamic reliability analysis of motor bearing in permanent magnet direct-drive system
|
Liangjun Wu, Wei Li, Yuqiao Wang, Song Jiang, Lianchao Sheng, Xuefeng Yang
|
p. 193-209
|
|
|
|
|
|
Enhancing the fatigue life of low-niobium compacted graphite cast iron exhaust pipes using multi-physical field coupled analysis and optimal design
|
Yongchuan Lin, Lusheng Liu, Yudong Zhang, Debin Lai
|
p. 211-221
|
|
|
|
|
|
Study on the dynamic response of steel frame joints under the combined action of explosion and fire
|
Xiuhua Zhang, Qizhou Guan, Shuang Yuan, Mingxin Chi
|
p. 223-234
|
|
|
|
|
|
Mechanical and thermal properties of Delonix regia seed filler reinforced vinyl ester composite for industrial application
|
Maharajan Prasanna Vengatesh, Balasubramaniam Stalin, Nagaraj Nagaprasad, V. Vignesh
|
p. 235-242
|
|
|
|
|
|
Bearing fatigue life analysis of hub motor under thermal-mechanical coupling condition
|
Fen Lin, Xiangyue Hou, Xuanjiang Liu, Qiaodong An, Hongwang Ma, Xiaolong Zhu, Liguo Zang
|
p. 243-256
|
|
|
|
|
|
Investigations on antifungal, dynamical, and thermal stability of Millettia pinnata fiber reinforced sawdust particulates thermoset polymer composite
|
Nagaraj Basavegowda, Pradeep Kumar Singh, Navin Kedia, Vinayagam Mohanavel, Raja Thandavamoorthy, Lalitha Gnanasekaran, Selvakumar Kathiresan, Manikandan Ayyar, Manzoore Elahi M. Soudagar
|
p. 257-264
|
|
|
|
|
|
Effect of ceramic fillers reinforced with sisal fiber epoxy composite : a novel way to develop the sustainable material
|
Vinayagam Mohanavel, Viyat Varun Upadhyay, Mamata Chahar, B. Angel, Sathish Kannan, Lalitha Gnanasekaran, Selvakumar Kathiresan, Manikandan Ayyar, Manzoore Elahi M. Soudagar
|
p. 265-271
|
|
|
|
|
|
Contact fatigue prediction model of carburized and quenched spur gears with multiaxial stress properties
|
Xiaopeng Wang, Shaoxiong Wan, Dongfei Wang, Zhongming Liu, Zhilong Yu
|
p. 273-284
|
|
|
|
|
|
Effects of deposition strategy on residual stresses in wire arc additive manufacturing of sandwich structures
|
Xiaolei Zhu, Yaosheng Liang, Feng Yang, Xiaofeng Lu, Jian Wang
|
p. 285-293
|
|
|
|
|
|
Intelligent shock absorbers for enhancing energy efficiency in electric vehicles
|
Alothmani Abdulwasea, Wenbo Liu
|
p. 295-305
|
|
|
|
|
|
Research status of laser cladding of Fe-based amorphous coatings
|
Chengming Cao, Yanhai Cheng, Hewei Zhu, Peng Liu, Kai Bai, Ruolan Zhang, Qi Sun
|
p. 307-321
|
|
|
|
|
|
(A) hybrid reliability evaluation method combined with accelerated life testing and imprecise models
|
Yi-Chao Yin, Yang Wu, Yu Zhou, Yuan-Jian Yang, Shuchen Cao, Mohammad Yazdi
|
p. 323-330
|
|
|
|
|
|
Finite element analysis of conventional impact absorbing materials and mechanical evaluation of fenosol foam applied to nuclear fuel transport casks
|
Chang Ho Kim, Yeong Hwan Jeon, Seung Gu Kang, Jae Moon Im, Kwang Bok Shin
|
p. 331-340
|
|
|
|
|
|
Research on key factors for optimizing packaging performance of oil-filled pressure sensors
|
Lijun Yang, Shubin Zhang, Fanjiang Kou, Ziqi Liu, Linpeng Xu, Jianwu Shen, Xuemin Wang
|
p. 341-349
|
|
|
|
|
|
(The) effect of grinding burns on microstructure and magnetization characteristics of G95Cr18 bearing steel
|
Ruotian Wang, Xiangyi Hu, Xiaoqiang Wang, Haoying Wei, Xuyang Bai
|
p. 351-362
|
|
|
|
|
|
Mechanical behavior and interface separation mechanism of bimetallic clad pipelines under reverse fault
|
Xuwei Zhang, Yun Yang, Changquan Hu, Jingxuan Xu, Jiahui Luo, Jianghai Yang, Wenfeng Yin, Jie Zhang
|
p. 363-372
|
|
|
|
|
|
Effects of tube arrangement on melting in latent heat thermal energy storage systems
|
Bo-ram Kim, Yu Sin Jeong, Tae Woo Kwon, Man Yeong Ha
|
p. 373-383
|
|
|
|
|
|
Exploring the sealing properties of thermodynamic lubrication in ultra-high-speed dry gas seals considering heat transfer modeling
|
Junhua Ding, Yue Miao, Shurong Yu, Shipeng Wang, Xuexing Ding
|
p. 385-399
|
|
|
|
|
|
Flow field analysis of key components in respiratory triggered tooling equipment
|
Min Lv, Peipei Zhang
|
p. 401-413
|
|
|
|
|
|
Investigation of the effects of design of the unit cell of TPMS structures on vortex generation performance using CFD simulation
|
Jong-Chan Beom, Gideon Simon Mduma, Hyeon Kim, Jong Bae Lee, Dong-Gyu Ahn, Sung Yong Jung, Young Dal Jeong
|
p. 415-425
|
|
|
|
|
|
Windage torque prediction of a disc-type flywheel under vacuum conditions using CFD analysis and experimental validation
|
Donghyun Lee, Byungock Kim, Byungchan Jeon, Changhwan Park
|
p. 427-436
|
|
|
|
|
|
Performance classification and prediction of additively manufactured negative stiffness honeycomb unit cell using a multi-fidelity model
|
Taemin Noh, Hyungdo Kim, Young-Jin Kang, Seunghun Baek, Yoojeong Noh
|
p. 437-453
|
|
|
|
|
|
Morphological and mechanical evaluation of epoxy hybrid composites reinforced with banana and jute cellulose
|
Ashok Kumar R., Ramesh Kumar A., Durairaj S., Sakthi Rajan C
|
p. 455-461
|
|
|
|
|
|
Machine learning based design optimization method for wave generators of harmonic drives considering multiple performance indicators
|
Jiawen Yang, Hongyu Wu, Xiaobiao Mu, Guoqiang Yang, Shaoze Yan
|
p. 463-476
|
|
|
|
|
|
Carbon nanotube- and graphene-reinforced composites : which is better for wind turbine blade applications?
|
Hyeong Jin Kim, Jin-Rae Cho
|
p. 477-486
|
|
|
|
|
|
Particle separation with microfluidic device using standing surface acoustic waves
|
Nesa Yaghoobi, Amirhosein Molaee, Ali Asadi, Shayan Valijam, Alireza Salehi
|
p. 487-493
|
|
|
|
|
|
Cutting force modeling method for milling process of thin-wall complex-surface workpieces considering effects of tool wear and varying-curvature feed path
|
Zheng Zou, Liang He, Hao Zhang, Benyuan Fu, Ruizhi Shu, Hui Jin, Yong Yang
|
p. 495-502
|
|
|
|
|
|
Influence of brazing currents on mechanical and corrosion properties of galvanized steel in gas metal arc brazing
|
Bhuwadol Thanathattakum, Sakdipat Jaturapronperm, Pongpak Chiyasak, Worawat Wattanathana, Trinet Yingsamphancharoen, Aphichart Rodchanarowan
|
p. 503-510
|
|
|
|
|
|
Effect of rib deposition on the fatigue performance of conventional Al 6061 T-fillet welds using WAAM
|
Jongho Jeon, Hansol Kim, Dongkyun Shin, Jungho Cho
|
p. 511-519
|
|
|
|
|
|
Optimization of high temperature die forging process parameters of GH4169 alloy low pressure two-stage turbine disk
|
Changshuai Shi, Yinlin Wang, Xiaohua Zhu, Ao Wang, Lin Gao, Pengchuan Li, Shengtao Liu
|
p. 521-532
|
|
|
|
|
|
Design of guard band chart based on measurement uncertainty : a worker-centric experimental approach using CMM
|
Insoo Choi, Sun Hur
|
p. 533-548
|
|
|
|
|
|
(An) efficient technique for CNC milling of conical surfaces with helical tool motion
|
Sotiris Omirou, Marios Charalambides, Michalis Menicou
|
p. 549-561
|
|
|
|
|
|
Commercialization of additive manufacturing material extrusion process parameter selection and optimization : a solar absorber housing fabrication application
|
Raja Subramani
|
p. 563-573
|
|
|
|
|
|
Data-mechanism fusion prediction of rolling force in hot rolling mill
|
Xiaomin Zhou, Tianliang Xiong, Huadong Qiu, Xiaoke Hu, Yuanlun Ma, Bin Wang
|
p. 575-584
|
|
|
|
|
|
Research on the influence of raceway surperfinishing process on the temperature rise characteristics of Si3N4 full ceramic ball bearings
|
Chao Wei, Shouqi Liu, Songhua Li, Yonghua Wang, Kun Wang, Yifeng Gao
|
p. 585-595
|
|
|
|
|
|
Automated fabric defect inspection with fuzzy c-means, conditional random fields and refined U-Net
|
Canan Tastimur
|
p. 597-607
|
|
|
|
|
|
Enhancing surface integrity and wear resistance of DMLS AlSi10Mg via ball burnishing
|
Gözde Ülkü Başsoy, Mahmut Çelik
|
p. 609-617
|
|
|
|
|
|
Towards industry 5.0 : integrating technical optimization of automated guided vehicles with human-centricity in sustainable production systems
|
Ruizhe Yin, Mohd Nizam Ab Rahman, Hawa Hishamuddin, Iliani Mohd Ikram, Muhammad Idham Sabtu
|
p. 619-632
|
|
|
|
|
|
(A) novel game-theoretic decision-making framework for autonomous vehicles in low-speed merge scenarios
|
Qian He, Lei Zhong, Xinchang Liu, Jianbin Qiu, Jiaqiu Zheng, Qiyu Wang
|
p. 633-642
|
|
|
|
|
|
Design and development of a robotic system for automatic loading with belt-combined robot arm
|
Li Jin, Liuyi Ling, Chengjun Wang, Yiming Liu, Wenhang Su
|
p. 643-653
|
|
|
|
|
|
(A) magnetically steerable soft gripper for navigating and grasping in constrained spaces
|
Xiao Dong, Hakjoon Lee, Awais Ahmed, Hongsoo Choi
|
p. 655-664
|
|
|
|
|
|
Variable admittance control of single-leg dynamics : a key to stable hexapod robot locomotion
|
Nan Li, Hongjun Xing, Ruixiang Huang, Xinqiang Zou, Weihua Li, Yiqun Liu, Haibo Gao, Liang Ding
|
p. 665-682
|
|
|
|
|
|
Numerical simulation of deposition characteristics of microorganisms and particles mixed fouling in sewage heat exchange tubes
|
Zhaoyi Zhuang, Keyue Nan, Jin Zhao, Caixia Zhang, Haiyang Yin
|
p. 683-697
|
|
|
|
|
|
Optimizing TDLAS analysis cycles for exhaust gas temperature measurement using XGBoost reinforcement learning
|
Doowon Choi, Hyeonae Jang
|
p. 699-712
|
|
|
|
|
|
Experimental investigation and techno-economic analysis of an integrated CO2 heat pump system with thermal energy storage
|
Yuxin Zheng, Tiantian Xu, Haihua Liu, Zizhen Huang
|
p. 713-722
|
|
|
|
|
|
Performance and comfort evaluation of wearable thermoelectric cooling and heating systems
|
Fujen Wang, Indra Permana, Nitesh Singh, Guo-Zhen Li, Yao-Tsung Lin
|
p. 723-737
|
|
|
|
|
|
Evaporation heat transfer correlation for CF3I/R1132a refrigerant blend in a horizontal tube
|
Amal Vasu, Young Soo Chang
|
p. 739-748
|
|
|
|
|
|
Optical characterization of pyrromethene dyes as seeded tracer for fuel PLIF in high temperature
|
Hyunchang Lee
|
p. 749-759
|
|
|
|
|
|
Thermal behavior analysis of a novel integrated electromechanical actuator
|
Linjie Li, Xuejiao Wang
|
p. 761-773
|
|
|
|
|
|
Design of pneumatic pressure nozzle for portable non-contact tonometer
|
Him Chan Kang, Jeong Heon Lee, Woo Sung Han, Jae B. Kwak
|
p. 775-782
|
|
|
|
|
대표어
한국학술지인용색인(NRF)
